29 Apr 2013

It's the responsibility to deny the cult religion in the world

When I play inline skate in my town, Some cult religionists are talking by theirselves to stop my playing inline skate there.
The japanese cult religionist makes wrong scale of value of art and something in the world. Why is it wrong ? Because the scale isn't expressed the real potencial which the people has.

Such musician who recorded in major label of the cult religion demands much respect !
I have a few respectable people in the world, just he is not such person !
The scale should be made by the critic and people who can think scientifically, equally and knows more well about their area not any religions,  I think.

Well,
Actually, It isn't easy to judge there is some problem on the law for traffic of this country.

I can judge whether I play inline skate here. The kids are saved too much by adults. Since last october, I haven't ever met the other inline skater.
Some days ago, at last I met the other skater.
Why is inline skater so rare ?

About 20 years ago, the rink for roller skating was broken by the city where I live. there, second gym was built.
Where can we play inline skate and roller skate ?

The law for traffic never says about it clearly.

If more skaters plays in the town, the cars will drive more slowly.
It's better for the people of course kids who live there, I think.

Is it hard to imagine that ? I don't think so.

detatched paint and welding small plates to front part and making seat

The paint was detached.
chemical detach ! is nice solution, I think.
It can be wipe off with water.
More one detaching was needed.
Completed.
I misunderstood that just one triangle plate was needed. Actually, more one triangle ( trapezuim is right ) and one square plates are needed.
 When I make a small plate, I use hand disk grinder to cut.
 Nice fitting ! A small hole on BBS needs to covered, I think.
 Welded the triangle plate, then the square plate was fitted.
 Welded. And more one square plate was welded at near BBS at the other side.
 For seat, more one front folk is used. This time, I can't get one for 20 inches tire, then I use one for 26 inches.
 It was cutted at 60 mm from the top. Then grinded to fit handle. It fitted just a little to front side. Because after that The iron rods for head rest will be welded the back side.
 Cramped and welded.
 Then the both side of handle were cutted at 140 mm from the center. I tried to use pipe cutter.
 How long the legs !
Can we get the cap for the edge of the handle ?
Fine.

28 Apr 2013

Connecting middle and rear part

To connect middle and rear part, It's needed boring for screw.
When I started making my python, I had mistake about it.
This time, I make smaller hole and widen with hand file.
At first making.
Next cramping and drilling.
 Then widen with file and adjust the diameter and the position.
 For suspension screw, the upper side hole is larger. It's about 20 mm.
Side view of the suspension.
 The rubber and circle iron plate are used.
2 washer are welded both sides.
Then grinding the surface to be smooth.
 Assembling.
The screw was used for rear before. then cutted the screw.
Ofcourse filing.
 done.
Over view.
The next task is welding the other front folk for seat.
 The front hub was welded on the edge of middle rectangular.
 The welded looks niecest ! However,I cleaned the flux.
Actually It wasn't enough. I repeated welding for sometimes to both front and back side. I had mistake which is bored the hub and I covered the hole with welding.
When 2 parts which is defference of the thickness, It's important to get it which is thicker or thinner, I think.
 Done. Side view.
Front View, Fine.

27 Apr 2013

makig rear part 4

To connect rear folk and middle rectangulr, Attaching Brass plates are needed.]
At first, I drew 36 x 70 mm square on graph sheet and cutted them then grewed on Brass plate and sawed.
 To adjust ment the width fit inside of the middle rectagular, hand grinder and hand file were used. The angles of inside are a little round, So to fit more perfect, The edges of the brass plates were filed.
 Basicaly, rear part fits on under face of inside the middle rectangular, So the seam joined face is used to upper side.
Then, to lost brass plates, The hooks were made by welding.
 They were grinded to the same height with the thickness of brass plates.
 The brass plates were grinded to fit the hooks, however, when the rear part and middle part are connected, the rear part should move smoothly.
 The rear parts putted in the middle rectangular.
This is nutral position. The next photo is most heavy weight position.
 The next task is boring for suspention.
Fine.

26 Apr 2013

Welding dropouts

At first, I thought that it's better to solder dropouts.
 So I setted up to solder them.
 from upper view.
 After putted flux on the parts, I putted on Silver solder rod.
 Then I burned them by burner. But I couldn't complete this task. I don't find why.
 Well, the next technique is welding. I setted up like this.
 Then welded them.
 How rough my technique !
 
 Then sanding was done roughly.
Not smooth welding.
Suddenly, it started rainning, then the sun light had comed again. then strong wind and rain has come. Today's working is finished.
fine.

25 Apr 2013

Making front part again 2

The task has kept.
I made triangle and square iron plates and put on those frame and cramped.
I think that the square plate better is welded after welding BBS.
The preparing is important, I think. We japanese say that the preparing is 80%, the job is 20 %.  Welding Those incisions and triangle part.
Next, BBS is welded.
The Left sylindrical one is BBS. The direction of upper side is before right side. To adjust angle of 90 degrees, the spacers are needed.
The triangle part is weded on this side. and this is on the spacer and cramped.
Horizontal !
The left sylindical one is BBS. We see from upper side.
Welded. the job is rough. I need being calme down.
Then The edges of rectangulars are burned and bended.
Then, the thicker part is grinded.
Welded.
Really, rough...
And ugly. I noticed the sound of the electric runs when the welding started.

The other BBS is needed on this front part.
Cutting for the other BBS. I used a handy disc grinder. This side has the triangle plate.
Then it was welded with my rough technique. The BBS has a tube for the seat. However it isn't used for the seat, It is used for the front derailleur Shimano FD-TX51. IT's cheaper one. So, The angle of the tube and these rectangulars are adjusted at 66 degrees.
I noticed forgetting weldeing a iron square plate near the vertical BBS.